How to use the Dark Knight SPIRIT Wax Vaporizer

STEPS FOR USE

Using the DarkKnight SPIRIT Vaporizer is extremely simple.

1 – Disassemble the glass body and nozzle from the unit’s main body

2 – Fill up the glass body (glass filter column) half way with water

3 – Add your media of choice to the unit’s atomizer / heating element with the tool included

4 – Re-insert the glass body into the unit’s main body until it is tightly secured. Assemble the glass nozzle to the glass body

5 – Press the unit’s activation button 5 times withing 2 seconds to turn the unit ON. The unit’s Red and Blue LEDs should light up brightly at this time.

6 – Press and hold the units ON button to vaporizer your media.

Note: The unit has an overheat protection function built in. This will automatically de-activate the unit from heating its atomizer if the atomizer is kept ON continuously for more than 15 seconds.

7 – Press the unit’s activation button 5 times withing 2 seconds once again to turn the unit OFF. The unit’s LEDs should light up brightly and remain off to indicate the unit has been shut down.

How to use the DVape 2in1 Vaporizer (Dry Herb & Wax)

STEPS FOR USE

Using the DVape 2in1 Vaporizer is extremely simple.

1 – Load your media in the unit’s atomizing chamber.

2 – By using the up or down temperature adjustment buttons, set your operating temperature of preference as shown in the unit’s LCD Display.

3 РOnce you have entered your temperature setting simply press the activation button and stand by until the hourglass status indicator turns to active status, meaning the desired temperature has been reached, and then simply enjoy great vapor.

Locking the unit off is as simple as repeatedly pressing the activation 5 times.  To unlock the unit for use once again, press the activation button again 5 times.

Further features are fully described in the product’s manual.

How to use the eVic VT by Joyetech

STEPS FOR USE

Operating this unit is easy.  With a simple and discrete selection knob the unit is designed to effortlessly allow you to browse through the MODs many features.

Follow these instructions when using the eVic VT.

1 РTo turn ON the MOD press its activation button 5 times.

2 – To use the MOD simply press and hold the activation button during operation.

Stealth Mode

– A stealth mode is available through which you may use the MOD with its LED display turned off. ¬†To enable this feature press the unit’s activation button and simultaneously turn the selection knob left for Stealth ON turn left again for Stealth Off.

Adjustment Lock

РThis feature allows the unit to prevent accidental VT / VW adjustments when the form pressing the selection knob inadvertently.  To enable this feature simple press the activation button and simultaneously turn the selection knob left for Adjustment Lock ON turn left again for Adjustment Lock Off.

Further features such as shifting between the special VT – Ni, VT – Ti, and VW Modes as well as unit specific safety modes (Temp protection, Temp alert, Atomizer Replacement, Atomizer, Short Circuit Protection, etc.) are all fully described in the product’s manual.

 

 

How to use the TREEBOX mini MOD by SMOK

STEPS FOR USE

Using the TREEBOX mini MOD is easy and systematic.

1 – Load your battery in the MOD.

2 РTo turn ON the MOD press its activation button 5 times.

3 – To use the MOD simply press and hold the activation button during operation. If no atomizer is connected, the MOD will show¬†“NO ATOMIZER” in its display.

Note: The unit has an operation protection feature that will force the device to stop if the activation button is held active for more than 12 seconds.  Also note that if the unit is left idle for more than 5 minutes it will shut itself down.

4 – Like with most MODs pressing the buttons below the display will allow for temperature or wattage control.

5 РAt any time during TC or VW operation pressing the activation button 3 times in 2 seconds will enter the MOD into its operation menu.  Long pressing the activation button during this time enables menu options selection.

6 РAt any time during TC or VW mode pressing both buttons below the display simultaneously will lock the device to avoid accidental operation.  To undo this setting both buttons need to be pressed simultaneously again.

While the device is Locked:

1 – Pressing the power button and the first button below the display simultaneously allows for the display to be rotated from left to right.

2 – Pressing the power button and the second button below the display allows for the resistance of the atomizer being used to be saved into the device’s memory.

While the device is Unlocked:

1 РSwitching between the TC and VW is as simple as pressing the activation button plus the first button underneath the display simultaneously

2 РWhile in TC mode pressing the activation button and the second button below the display simultaneously will allow for the selection three different vape settings defined as NORMAL, HARD or SOFT.

3 Р While in TC mode Coil Material type may be selected from the operations menu.  The MOD allows for Nickel, Titanium and Stainless Steel coil specific types for more precise and efficient use.

4 РAlso while in TC mode the operations menu allows for a Temperature Coefficient of Resistance (TCR) setting to be adjusted that will further improve the operating temperature on the MOD per the coil being used so that the best tasting vapor is achieved.

5 РFinally, TC mode also allows for an Adjustable Initial Resistance setting where the MOD may be set with an atomizer initial resistance providing for even further customized operation.

6 РTurning the unit OFF is as simple as pressing the activation button 5 times.

Note: ¬†The TREEBOX mini is also full of safety¬†features that are specified on the unit’s manual.

Batteries are NOT included with this unit. One 18650 Battery is recommended for use.

 

How to use Asolo MOD by iJoy

STEPS FOR USE

Using the Asolo MOD is easy and systematic.

1 – Load your batteries in the MOD.

2 РTo turn ON the MOD press its activation button 5 times.

3 – To use the MOD simply press and hold the activation button during operation. If no atomizer is connected, the MOD will show¬†“NO ATOMIZER” in its display.

Note: By pressing the T button, the unit will switch between its VW (Variable Wattage) and TC (Temperature Control) modes. During TC mode the unit will operates as a SMART DEVICE effectively LEARNING how to most efficiently energize the connected atomizer of choice to provide you with the best tasting vapor possible.

 

4 РWhile in TC mode pressing the + or the Рon the T button will allow you to operate as HARD or SOFT modes which increase or decrease the SMART operating temperature of the MOD by increasing or decreasing the temperature through percentage increments.

Note:  The unit is also capable to store in memory what it learned from the Atomizers being used so that as you switch your atomizers it can adjust back to previously LEARNED coils based on their specific resistance.

 

5 – This MOD also runs¬†Titanium and Nickel Modes.¬†¬†For these modes simply press the T button three times and a selection screen will appear on the unit’s display. ¬†Then select your desired temperatures and modes by pressing the + or – ¬†on the T button.

6 – ¬†Further, the unit has a¬†“Dry Hit”¬†or E-Liquid sensing feature that will stop the unit from working if you run out of eJuice half way or prior to inhaling your vapor. ¬†This feature makes the SMART device SAFE as well. ¬†A MOD first.

7 РFinally the MOD has a PASSWORD function that will secure your device at all times making it, along with all its features and modes, the most sophisticated MOD available on the the market today.

8 РTo turn the unit OFF press the activation button 5 times.

 

Note: ¬†More information and details are found on the unit’s Manual.

Batteries are NOT included with this unit. 18650 Batteries are recommended.

How to use ETOP 30 MOD by iJoy

STEPS FOR USE

Using the ETOP 30 510 MOD is easy and systematic.

1 – When you load your battery the MOD will flash its LED light in white color once to indicate the battery has been loaded correctly.

2 – To turn ON the MOD press its activation button 5 times. Once you do its LED light will flash 3 times in white color.

3 – To use the MOD simply press and hold the activation button during operation.

Note: By rotating the dial you may manually adjust your unit’s output power from 8-30W. With every successfull selection the MOD LED light will flash. If A is selected the MOD will AUTOMATICALLY adjust its output power to suit whatever atomizer is connected to the unit.

4 – The unit is also designed to notify the user what is the remaining status of its battery.

The LED light will flash in different colors depending on battery power.

Blue for 3.9V or more and battery power over 80%

Green for 3.6V or more and battery power over 60%

Red for 3.3V or more and battery power over 30%

Note: When the battery voltage is less than 3.3V the LED will flash RED 10 times indicating its time to recharge the battery.

5 – To turn the unit off press the activation button 5 times. Its LED ligth will flash 3 times in white color to indication that the unit has been turned off.

Battery is NOT included with this unit. 18650 Battery is recommended.

How to use NVape Wax Vaporizer

STEPS FOR DAILY USE

1 – Press the activation botton FIVE times and the light around the activation button will flash BLUE 5 times indicating the unit is “ON”.

2 – Once you have shatterd your wax into vaporizing chamber.

3 – Close the vaporizing chamber by reinserting the glass mouthpiece on the atomizer.

4 – Activate the heating element of the vaporizer by keeping the activation button pressed. While the button remains pressed the vaporizer will gradually heat Wax until it is slowly vaporized.

5 – Proceed to inhale through the mouthpiece while the button is pressed until you consume all the vapor.

6 – Once you have consumed all your herb unplug the mouthpiecce and use the cleaning brush provided to clean the chamber.

7 – Go back to STEP 2

Note: Before recharging the vaporizer be sure to bring to its OFF state by pressing the activation button FIVE times.

 

ROUTINE MAINTENANCE

1 – Be sure the vaporizer is turned off.

2 – Unplug the mouthpiece and remove the units atomizer as needed.

3 – Use boiling water to remove any leftover wax from the atomizer. Do this as needed so that all remaining residues are removed and air flow and heat exchange is restored.

4 – Allow all components to dry at room temperature.

5 – Once the components are dry reassemble them back together.

6 – Finally proceed to follow the STEPS FOR DAILY USE.

Note: Typically ROUTINE MAINTENACE is required once a month dependant of use.

How to use Falcon Herb Hydro Vaporizer

STEPS FOR DAILY USE

1 – Load your grinded herbs in the units vaporizing chamber. Then remove water lid to fill the unit with distilled water.

2 – To turn on the FALCON unit press its activation button. Initially the LED bar on the back of the unit will display the remaining battery charge level.

3 – By pressing the activation button once again you will be able to select one of the 5 preset temperature settings.

4 – Once the desired temperature pre set is selected the vaporizer will flash its LED lights until the desired temperature is reached. After this the vaporizer LED light will remain iluminated in the corresponding color of the temperature pre set selected.

5 – To shut down the unit press and hold its activation button until the units LED lights turn off.

 

ROUTINE MAINTENANCE

1 – Use the cleaning brush included with the unit to remove any spent herb from its vaporizing chamber.

2 – Use the unit’s Allen tool to unmount the bottom end of the vaporizer. Once you do proceed to clean its water tank. It is recommended to clean the water tank at least once a week.

How to use BlissVape (2 in 1) Vaporizer

STEPS FOR DAILY USE

1 – Press the activation botton FIVE times and the light around the activation button will flash BLUE 5
times indicating the unit is “ON”.

2 – Once you have grinded your Dry Herb load it into the Dry Herb vaporizing chamber.

Note: The atomizer with the exposed heating coil is designed for vaping WAX.

3 – Close the vaporizing chamber by inserting the glass mouthpiece before consumption

4 – Activate the heating element of the vaporizer by keeping the activation button pressed. While the button remains pressed the vaporizer will gradually heat the Dry Herb until it is slowly vaporized.

5 – Proceed to inhale through the mouthpiece while the button is pressed until you consume all the vapor.

6 – Once you have consumed all your herb unplug the mouthpiece, empty the vaporizing chamber from
the spent herbs and use the cleaning brush provided to clean the chamber.

7 – Go back to STEP 2

Note: Before recharging the vaporizer be sure to bring to its OFF state by pressing the activation button FIVE times.

 

ROUTINE MAINTENANCE

1 – Be sure the vaporizer is turned off.

2 – Unplug the mouthpiece and remove the units atomizer as needed.

3 – Wet a cotton swab with rubbing alcohol and use it to remove any resin or left-over from each piece
used in order to leave the atomizer clean from debris. Do this with as many wet cotton swabs as
needed so that all remaining residues are removed and air flow is restored.

Note: When cleaning the wax atomizer use boiling water or steam to remove any left over wax.

4 – Allow all components to dry at room temperature.

5 – Once the components are dry reassemble them back together.

6 – Finally proceed to follow the STEPS FOR DAILY USE.

Note: Typically ROUTINE MAINTENACE is required once a month dependant of use.

How to use DM-T Vaporizer

STEPS FOR DAILY USE

1 – Press the activation botton continuously until the display indicator lights up and reads “ON”.

Note: You will also see the battery charge status along with the number of “hits” the vaporizer has provided.

2 – Once you have grinded your Dry Herb load it into the vaporizing chamber until it fills 2/3 of it

3 – Close the vaporizing chamber by screwing the mouth piece all the way in

4 – Activate the heating element of the vaporizer by keeping the actication button pressed. While the button remains pressed the vaporizer will gradually heat the Dry Herb until these are slowly vaporized.

5 – Proceed to inhale through the mouthpiece while the button is pressed until you consume all the vapor from your Herbs.

Note: As you hit / puff your herbs the vaporizer will keep count and show it in its display.

6 – Once you have consumed all your herb unscrew the mouthpiecce, empty vaporizing chamber from the spent herbs and use the cleaning brush provide to clean the chamber.

7 – Go back to STEP 2

Note: Before recharging the vaporizer be sure to bring to its OFF state by repeatedly pressing the activation button until “OFF” is shown in its display.

 
ROUTINE MAINTENANCE

1 – Be sure to unscrew the battery from the vaporizing chamber and the mouthpiece.

2 – Dissassemble the mouthpiece and the vaporizing chamber in their entirety, piece by piece.

3 – Wet a cotton swab with alcohol and use it to remove any resin or left-over from each piece as needed in order to leave the vaporizer clean. Do this with as many wet cotton swabs as needed so that all remaining pollutants are removed and air flow is restored.

4 – Allow all components to dry at room temperature and wait until all alcohol evaporates.

5 – Once the components are dry reassemble them back together and screw in the mouthpiece and vaporizing chamber with the battery.

6 – Finally proceed to follow the STEPS FOR DAILY USE.

Note: Typically ROUTINE MAINTENACE is required once a week depending on its use.

How to use R2-D2 MOD

STEPS FOR USE

Using the R2-D2 510 MOD is easy and systematic.

1 – Press its activation button repeatedly (3 times within 2 seconds) to enter the mode selection menu.

2 – Once in the selection menu press the activation button once again to scroll through each of the
different menu options (Options 1 – 7).

Option 1: Watt Up (5.0W – 15.0W) / Voltage Up (3.0V – 6.0V)
Allows you to control wattage settings in increasing values

Option 2: Watt Down (15.0W – 5.0W) / Voltage Down (6.0V – 3.0V)
Allows you to control wattage settings in decreasing values

Option 3: Out (ON / OFF)
Allows for custom locking the MOD output between ON / OFF

Option 4: Battery Voltage
Displays current battery Voltage

Option 5: LCD Display
Allows you to chose what is displayed by the LCD Display when the activation button is
pressed once. Choose between: Wattage or Voltage (depending on Option 7), Battery,
Resistance.

Option 6: LCD (ON / OFF)
Allows you to turn ON / OFF the LCD Display on the MOD

Option 7: Wattage/Voltage
Allows you to control the MOD based on Wattage Output or Voltage Output
3 – To select an Option simply wait while the option is displayed on the LCD Screen for 2 seconds and
the MOD will automatically provide you access settings to the selected option.

4 – Once you customize your settings of the selected option, simply wait 2 seconds and the MOD will
enable the selected option based on the settings selected.

5 – After settings are selected and set the MOD will display the last setting set everytime the activation
button is pressed once.

6 – You may customize the MOD to display between Wattage or Voltage, Battery & Resistance.

7 – Finally this MOD allows the user to control the airflow that is being suplied to the 510 MOD compatible
TANK used with a unique airflow valve control setting at the tip of the MOD.

8 – Only use the supplied battery charger to charge the 18650 battery included with the MOD.